WEEE NL: 3505
WEEE DE: 37281017
WEEE AT: 40133
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
LED’s
work
A
BRAND
SHADA
GB
Operating Manual
Packaging contents:
1x Rechargable Multi-Function Light
1x 230 V USB power supply
1x 12
…
24V USB car adapater
1x USB Charging cable
1x Operating manual
I
mportant
: please read these instructions carefully. Note the
safe operational requirments, warnings and cautions, use this
product correctly and with care for the purpose for which it is
intended.Failure to do so may cause damage and/or personal
injury and will invalidate the warranty. Please keep instruc-
tions safe for future use.
1. SAFETY INSTRUCTIONS
1.1. GENERAL
• Ensure the worklight is correctly charged before initial use.
• DO NOT cover or block the lens during use.
• DO NOT shine directly into your, other person‘s or animal‘s
eyes.
• DO NOT allow children to use the worklight
• DO NOT handle or move the worklight whilst it is being
charged.
• DO NOT use the worklight if you suspect that the battery
or the worklight casing is damaged.
• Ensure replacement batteries are genuine batteries of the
same rating.
• Ensure the worklight is unplugged and allowed to cool
before attempting any cleaning or replacement.
• When not in use, store the worklight in a safe, dry, child-
proof location.
1.2 BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
• DO NOT attempt to open, disassemble, modify or service
the battery.
• Ensure the charger is switched off and disconnected from
the worklight before attempting to open the lamp unit.
• DO NOT expose to temperatures above 40 °C
• DO NOT crush, puncture, short external contacts or dispose
of in fire or water.
• Replace only with the batteries designated for this product.
• Dispose of the old batteries in accordance with local
authority battery regulations. DO NOT dispose of with
regular refuse.
• If the electrolyte in the cells contacts the skin, wash thoro-
ughly with soap and water.
• If the electrolyte in the cells gets into the eyes, rinse
thoroughly with cool water and seek immediate medical
attention.
1.3 Electrical safety
Use only the supplied mains charger plug for connecting work-
light to the mains power supply.Only use the supplied adaptor
for connecting to a vehicle 12V -24V accessory socket.
Warning!
It is the user’s responsibility to read, understand and
comply with the following electrical instructions: You must
ensure the risk of electric shock is minimized by the installa-
tion of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distributi-
on board. We also recommend that an RCD (Residual Current
Device) is used with all electrical products, particularly porta-
ble equipment which is plugged into an electrical supply not
protected by an RCCB.
You must also read and understand the following instructions
concerning electrical safety.
You must ensure that you:
• Inspect the charger plug,cable and connector for wear and
damage to ensure items are safe before connecting to the
mains power supply. If worn or damaged DO NOT use.
• Check cables are always protected against short circuit and
overload.
• Important:Check that the voltage marked on the charger
plug is the same as the power supply to be used.
• Uncoil the cable between charger and the worklight.
• DO NOT pull the charger plug from the mains socket by
the lead.
• DO NOT use any other type of charger with this product.
• DO NOT place the connector into any area of the worklight
except the correct jack inlet socket.
• DO NOT try to take the charger plug apart.
• DO NOT use the charger plug to charge or power any other
electrical item.
• DO NOT get the charger wet,or use in wet, damp condi-
tions (for indoor use only).
2. INTRODUCTION
2W (4x 0,5 watt SMD) + 2 watt CREE-LED rechargeable work-
light,2W SMD to be used as an inspection lamp or 2W LED on
the top to be used as a torch. Magnets on the the rear on a 180
degree swivel Clip, supplied with 230 V mains USB charger and
12-24V USB car charger.
3. OPERATION
3.1 CHARGING
Warning
! Ensure that you read, and fully understand the safety
instructions before use.
3.1.1 Charge the batteries before use.
Important
: Ensure the worklight is turned „Off“ while char-
ging. Failure to do so will damage the charger plug/vehicle
plug.
3.1.2 Connect the charging plug into the charging socket, which
is located on the rear of inspection lamp. Connect the 230V
charger or 12V-24V DC charger to a power supply.
3.1.3 The charging LED indicator under the front LED will BLINK,
charge for up to 4 hours.
3.1.4 Disconnect the charger from the worklight when it is fully
charged.
3.2 OPERATTION
Caution
! Never shine the LED light directly into your or any one
else’s eyes.
3.2.1 Press the on/off switch ,run through the sequence of mo-
des (Front light/top LED on and off)
4. MAINTENANCE
Keep the worklight clean from dirt and grease, using a damp
cloth. Do not submerge in water.
Notes on Disposal
Old units, marked with the symbol as illustrated,
may not be disposed of in the household rubbish.
You must take them to a collection point for old units (enquire
at your local authority) or the dealer from whom you bought
them. These agencies will ensure environmentally friendly
disposal.
Care and warranty
Before cleaning the unit, disconnect it if necessary from other
components; do not use aggressive cleaning agents.
The unit has been carefully checked for defects. If nevertheless
you do have cause for complaint, please go back to the retailer
where you have bought the product together with your proof
of purchase. We offer a 2 year warranty from date of purchase.
We are not liable for damage arising from incorrect handling,
improper use or normal wear and tear. We reserve the right to
make technical modifications.
Visit us online at
www.shada.nl
for more information about
our products and our company.
This product Complies with the following direc-
tives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) can
be found here:
http://www.shada.nl/uploads/
DoCs/index.html
Technical specifications
Art no.
Total output (W):
Luminous flux
(working light/flashlight)
(lm):
Charging time (h):
Burning time
(working light/flashlight)
(h):
Protection class:
Input voltage (V DC):
Warm up time (s):
Switch cycles:
LED lifetime (h):
Colour temperature (K):
Colour Rendering Index:
Beam angle
(working light/flashlight)
:
Battery
700319
2/2
180/160
~ 3-4
~ 3
IP44
5V 1A (USB)
<1
30.000
30.000
6.500
Ra>70
60°/15°
Li-Ion 3,7V 1600mAh 5,92Wh
