SGC ADSP FT817 Скачать руководство пользователя страница 1

 

 

 

FT817 ADSP

2

 Installation 

 

Low Power Board 

 

Catalog Number 70-11 

 

SGC Inc. SGC Building, 13737 SE 26th St. Box 3526  Bellevue, WA. 98009 USA   

Fax: 425-746-6384,  Tel: 425-746-6310 or 1-800-259-7331 

E-mail: [email protected] • World Wide Web: 

www.sgcworld.com

 

©April 2003 SGC Inc 

 

This document describes procedures that could result in voiding of the warranty of your radio.

 

If these procedures are not precisely and properly carried out, it could result in a radio that does not work or is damaged. 

Furthermore, while reasonable efforts have been made to assure the accuracy of this information, it is possible that there are some errors, or that your radio is of a slightly different 

version than the one used for testing and thus, differences may exist. You are expected to take total responsibility for your own actions. 

It is assumed that anyone following suggestions made in this document is already thoroughly familiar with the technologies and techniques involved and possesses the necessary 

skill and knowledge to make their own judgment as to the appropriateness and validity of the information. 

If you choose to do the installation outlined, you do so at your own risk. You are solely responsible for any damage, voiding of warranty, or other harm that may come about 

by following these procedures. It is very strongly recommended that, if you maintain your own radio, you thoroughly familiarize yourself with the transceiver service manual.  

If you don't have one, get one!

 

 

CAUTION: Soldering and desoldering of very small Surface Mount Components may be required to perform this installation 

 

IMPORTANT NOTE: Support for the ADSP

2

 board will be provided by SGC 

exclusively by email. Please write to 

[email protected]

 for assistance if needed. 

1. Technical Specifications 

 

Specification 

Low Audio 

High Audio 

Size 

1.7 X 1.475” 

2.645 X 1.475” 

Weight 

0.6 oz 

1.1 oz 

 

 

 

Audio Limits 

 

 

   Min Input 

10 mv RMS 

100 mv RMS 

   Max Input 

150 mv RMS 

5 volt RMS 

   Max Output 

.5 v RMS 

9 v RMS 

Power Output   

 

5 Watts RMS 

 

 

 

Current Consumption 

 

 

    idle 

80 mA 

110 mA 

    full out 

80 mA 

500 mA 

 

 

 

 

X1 

X2 

Noise Reduction 

13 dB 

26 dB 

Time Delay 

6.5 ms 

13 ms 

Tone Rejection 

-50 dB 

-65 dB 

 

 

 

Filters (3dB Bandwidth) 

 

 

   Voice 

300-2100 Hz 

 

    CW Wide 

400-900 Hz 

 

    CW Narrow 

600-700 Hz 

 

Out of Band Rejection 

-45 dB

 

 

 

Содержание ADSP FT817













Отзывы: