sewerin EX-TEC PM 4 Скачать руководство пользователя страница 64

Страница: 64 / 98

5 Maintenance

5.3.3

Confirming adjustment

As part of the adjustment process, each completed test must

be stored in memory. This is done via the

Inspection OK

item. As a result:

The test date is saved.

The next adjustment date is calculated based on the specified

inspection interval.

An inspection block (if set) is triggered.

Confirm the completed adjustment on the device as follows:

Using the or key, select the

Inspection OK

menu item.

Confirm your selection with the

key.

5.4

Servicing

The device must only be serviced and repaired by SEWERIN

Service or a qualified service technician/company authorised by

SEWERIN.

Send the device to SEWERIN for repairs and for annual main

tenance.

Note:

If there is a service agreement in place, the device can

be serviced by the mobile maintenance service.

The inspection plate on the device shows

confirmation of the last maintenance and the

next scheduled maintenance.

Содержание EX-TEC PM 4



































































































Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды

sewerin EX-TEC PM 4, Руководство по эксплуатации

Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды