sewerin EX-TEC PM 4 Скачать руководство пользователя страница 23

Страница: 23 / 98

3 Operation

3.2.1

User menu

Measuring mode comprises the following functional scope:

–

Zero point correction

– Application selection

– Confirmation of function control

–

Gas type (optional)

The functions in the user menu are described in Sections 3.2.2

to 3.2.8.

To select functions, you must first access the

user menu

Press the key or the

key for approximately 2 seconds.

The

user menu

is displayed:

zero point
House
Enclosed spaces
Warning %LEL
Measuring vol%
inspection ok
type of gas

To move between menu items:

Navigate up and down in the menu by briefly pressing the

or key.

Confirm your selection by briefly pressing the

key.

If the selection is not confirmed, the display reverts back to meas

uring mode after approximately 10 seconds.

Содержание EX-TEC PM 4



































































































Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды

sewerin EX-TEC PM 4, Руководство по эксплуатации

Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды