sewerin EX-TEC PM 4 Скачать руководство пользователя страница 18

Страница: 18 / 98

3 Operation

Operation

3.1

General information on operation

3.1.1

Operator guidance

There are two ways to operate the

EX-TEC PM 4

–

Operator guidance by application

–

Operator guidance by sensor

These operating instructions are based on operator guidance by

application in accordance with DVGW Note G 465-4:

– Testing in houses/buildings (

House

application)

– Testing in enclosed spaces (

Enclosed spaces

application)

– Warning against explosive gas concentrations

(

Warning %LEL

application)

– Measurement of gas concentrations

(

Measuring VOL%

application)

Note:

The factory default operator guidance setting for the

device is

Application

. This can be changed to

Sen-

sor

in the advanced settings (see Section 3.3.4.2).

Содержание EX-TEC PM 4



































































































Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды

sewerin EX-TEC PM 4, Руководство по эксплуатации

Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды