sewerin Ex-Tec GM 4 Скачать руководство пользователя страница 88

Страница: 88 / 102

11 Technical aspects

11.3

Error messages

An error message is displayed in case of any failure during ope

ration. The error No. and error description will be indicated.

Error code LCD (error

description)

Cause

Remedy

F09

no adjustment:

no adjustment data

present

carry out an adjust-

ment

F10

adjustment

error:

zero point in the ppm

range

check test gas or re-

peat adjustment

F13

adjustment

error:

sensitivity in the ppm

range

check test gas or re-

peat adjustment

F51 – F54

system error

component error

witch instrument off

and on again or con-

tact SEWERIN service

F 59

voltage supply voltage outside the

permitted range

contact Sewerin serv-

ice only

F100

pump power

pump power too low

check filters in the in

strument and probes.

Please observe the

instructions in section

9.9: Adjusting pump

operation

Note:

If any other error codes appear, please contact

SEWERIN service!

Cause:
Remedy:

Programm defect

SEWERIN service

F09 – F15

temporary errors

F40, F100

clearable errors

F51 – 54, F59 – F62

system errors; switch instrument off

Содержание Ex-Tec GM 4







































































































Результаты поиска

Содержание Ex-Tec GM 4

Отзывы:

Похожие инструкции для Ex-Tec GM 4

Бренды по названию

Популярные бренды

sewerin Ex-Tec GM 4, Руководство по эксплуатации

Результаты поиска

Содержание Ex-Tec GM 4

Отзывы:

Похожие инструкции для Ex-Tec GM 4

Бренды по названию

Популярные бренды