SEW MOVITRAC LTP series Скачать руководство пользователя страница 7

Страница: 7 / 80

Operating Instructions – MOVITRAC® LTP

Operation and servicing

Safety Notes

2.2

Operation and servicing

•

Dangerous voltages

are present in the

output terminals

and the

cables and

motor terminals connected to them when the unit is switched on

. Dangerous

voltages may also be present when the unit is inhibited and the motor at a standstill.

• The unit is

not

necessarily

deenergized

when the

LEDs and the 7-segment

display are off

•

Safety functions inside the unit

or a

mechanical blockage

may cause the

motor

to stop

. The

removal of the source of the malfunction

or a

reset

can result in an

automatic restart of the drive

. If, for safety reasons, this is

not permissible

for the

driven machine,

disconnect the unit from the supply system

before correcting the

fault.

WARNING

Danger of electrical shock. High voltages are present in the terminals and in within the
drive for up to 10 minutes after the electrical supply has been disconnected.
Severe or fatal injuries.
• Disconnect and isolate the MOVITRAC

LTP from the electrical supply at least 10

minutes before commencing any work on it.

Содержание MOVITRAC LTP series

















































































Результаты поиска

Содержание MOVITRAC LTP series

Отзывы:

Похожие инструкции для MOVITRAC LTP series

Бренды по названию

Популярные бренды

SEW MOVITRAC LTP series, Руководство по эксплуатации

Результаты поиска

Содержание MOVITRAC LTP series

Отзывы:

Похожие инструкции для MOVITRAC LTP series

Бренды по названию

Популярные бренды