SEW movifit mc Скачать руководство пользователя страница 138

Страница: 138 / 184

Operation

MOVIFIT® MC status LEDs

Operating Instructions – MOVIFIT

138

7.1.6

Option-specific LEDs

PROFIsafe option S11

WARNING

Observe the "MOVIFIT

MC/FC – Functional Safety" manual when using the

PROFIsafe option S11.

Severe or fatal injuries may result.

• If you use the PROFIsafe option S11, observe the additional notes on diagnos-

tics and operation as well as the safety conditions specified in the
"MOVIFIT

MC/FC – Functional Safety" manual.

WARNING

Danger due to incorrect interpretation of the "FDI.", "FDO.", "STO" and "F-STATE"
LEDs.

Severe or fatal injuries.

• The LEDs are not safety-related and may not be used as a safety device.

This chapter describes the option-specific LEDs for PROFIsafe option S11. In the fol-
lowing figure, these LEDs are shown as dark. In the sample figure, the PROFIBUS
version is shown with "Technology" function level:

DI03

DI01DI02

DI00

DI04DI05DI06DI07

DI08DI09DI10DI1

DI12/DO00

DI13/DO01

DI14/DO02

DI15/DO03

MOVIFIT

SF/USR

BUS-F

RUN

F-ST

FDI00FDI01FDI02FDI03FDO00

FDO01

24V

-C

24V

-S

9007200284854539

"FDI.." LEDs

The following tables show the statuses of the "FDI00" – "FDI03" LEDs.

LED

Meaning

Yellow

Illuminated

HIGH level at input F-DI..

Off

LOW level at input F-DI.. or open

"FDO.." LEDs

The following tables show the statuses of the "FDO00" – "FDO01" LEDs:

LED

Meaning

Yellow

Illuminated

F-DO.. output is active.

Off

F-DO.. output is inactive (switched off).

19484828/EN – 01/2015

Содержание movifit mc

























































































































































































Результаты поиска

Содержание movifit mc

Отзывы:

Бренды по названию

Популярные бренды

SEW movifit mc, Руководство по эксплуатации

Результаты поиска

Содержание movifit mc

Отзывы:

Бренды по названию

Популярные бренды