SEW MDR60A Скачать руководство пользователя страница 65

Страница: 65 / 148

Operating Instructions – MOVIDRIVE® MDR60A/61B

Setting for CFC/servo mode

Startup (MDR60A0150/0370/0750 and MDR61B1600/2500)

5.6

Setting for CFC/servo mode

If you use CFC mode, you have to make the corresponding selection during startup. The
following section illustrates the selection and the further procedure depending on the
MOVITOOLS

MotionStudio version.

• Select operating mode CFC "current-controlled with feedback".

•

Example A (version 5.7 with ServicePack 1):

Activate the checkbox "Unit is in DC

link connection...".

•

Example B (version 5.7 without ServicePack 1)

you additionally have to halve the

gain of the current controller (Kp I controller).

– Press <Shift> + Next> to confirm your selection.

– Change the setting Kp I controller setting to 50% of the suggested value.

MOVITOOLS

MotionStudio

Example A: Version 5.7 with ServicePack 1
(In preparation)

Example B: Version 5.7 without service pack
(latest version)

INFORMATION

The following unit combinations do not allow the operation of synchronous servomo-
tors with MOVIDRIVE

• MOVIDRIVE

MDR61B regenerative power supply unit size 7 in DC link connec-

tion with MOVIDRIVE

MDX61B inverters size 0 – 6

• MOVIDRIVE

MDX61B inverters size 7 in connection type A or B with

MOVIDRIVE

MDX61B inverters size 0 – 6

Содержание MDR60A





















































































































































Результаты поиска

Содержание MDR60A

Отзывы:

Похожие инструкции для MDR60A

Бренды по названию

Популярные бренды

SEW MDR60A, Руководство по эксплуатации

Результаты поиска

Содержание MDR60A

Отзывы:

Похожие инструкции для MDR60A

Бренды по названию

Популярные бренды