SEW MDR60A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 148

background image

22

Operating Instructions – MOVIDRIVE® MDR60A/61B

4

Installation notes

Installation (MDR60A0150/0370/0750 and MDR61B1600/2500)

4.1.2

Minimum clearance and mounting position

• Observe the minimum wire bending spaces in accordance with EN 61800-5-1.

• Only install the units

vertically

. You must not install them horizontally, tilted or upside

down.

• Ensure unobstructed cooling air supply and make sure that the units are not sub-

jected to heated air from nearby components.

• Observe the following clearances:

•

MDR60A0150/0370:

Above and below at least 100 mm (3.9 in).

•

MDR60A0750 and MDR61B1600/2500:

Above at least 100 mm (3.9 in). With

temperature-sensitive components such as contactors or fuses, at least 300 mm
(11.8 in).

• No clearance required on the side The units can be arranged directly next to one

another.

4.1.3

Separate cable ducts

• Route

power cables

and

electronics cables

in

separate cable ducts

.

4.1.4

Fuses and earth-leakage circuit breaker

• Install the

input fuses at the beginning of the supply system lead

after the supply

bus junction (observe the wiring diagram for basic unit, power section and brake).

• SEW-EURODRIVE recommends not to use earth-leakage circuit breakers in plants

with frequency inverters as an earth-leakage circuit breaker reduces the plant avail-
ability.

4.1.5

Polarity of the DC link connections

• You must observe the

correct polarity of the DC link connections.

False polarity

of the DC link connections will cause

irreparable damage to the connected units!

The DC link connection carries a high DC voltage (approximately 900 V). Twist the
DC link cables and only route them inside the control cabinet.

4.1.6

Connecting inverters to the MOVIDRIVE

®

MDR60A/61B regenerative power supply unit

• If you use cables to connect inverters to the regenerative power supply unit, you have

to connect the inverters in

star connection

. Make sure to consult the installation

notes in the operating instructions for the inverter.

WARNING

Wrong type of earth-leakage circuit breaker installed.

Severe or fatal injuries.

The unit can cause direct current in the protective earth. If you use an earth-leakage
circuit breaker (FI) for protection in the event of direct or indirect contact, you may only
connect a type B earth-leakage circuit breaker (FI) on the supply side of the device.

«
...
20
21
22
23
24
...
»

Содержание MDR60A





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MDR60A

Бренд: 3M Страницы: 11

Бренд: Gallagher Страницы: 90

Бренд: Gallagher Страницы: 24

Бренд: Ratio Electric Страницы: 4

Бренд: Laser Страницы: 8

Бренд: Makita Страницы: 1

POWERFIX KH4055

Бренд: Powerfix Страницы: 4

Бренд: S.E.F.A Страницы: 26

Бренд: P.Lindberg Страницы: 76

Бренд: QJE Страницы: 7

YS6801-UC/SM-SO301

Бренд: Yolink Страницы: 24

Бренд: Ferm Страницы: 112

Бренд: TDK-Lambda Страницы: 2

Бренд: BorMann Страницы: 28

Бренд: VONROC Страницы: 84

Бренд: Napa Страницы: 12

Carlyle TW12RH2

Бренд: Napa Страницы: 12

Бренд: FOREDOM Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды