SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 20

Страница: 20 / 172

Mechanical Installation

Installation instructions

Operating Instructions – MOVIFIT

-FC

Mechanical Installation

4.1

Installation instructions

• Mount MOVIFIT

only on a level, vibration-proof and torsionally rigid support struc-

ture, as described in the section "Approved installation position".

• Use suitable cable glands (use reducing adapters if necessary). For versions with

plug connectors, make sure to use the matching mating connectors.

• Use screw plugs to seal cable entries not in use.
• Use protective caps to seal plug connectors not in use.

4.2

Approved installation position

The following figure depicts the approved installation position for MOVIFIT

MOVIFIT

is attached by means of a mounting plate using the four screws already

installed in the mounting surface. For further information, refer to section "Assembly
instructions" (see page 21).

CAUTION

Risk of injury due to protruding parts, especially the mounting rail.
Risk of cutting or crushing.
• Cover sharp and protruding parts, especially the mounting rail, to protect against

injury and damage.

• Make sure that only trained specialists carry out the installation.

812409611

TIP

This section uses the version with terminals and cable bushings as an example.
However, the assembly instructions are applicable for all versions.

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 20 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: