SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 132

Страница: 132 / 172

Technical Data

Version with operating point 460 V/60 Hz

132

Operating Instructions – MOVIFIT

-FC

9.3

Version with operating point 460 V/60 Hz

MOVIFIT

unit type

MTF11A

003-503

MTF11A

005-503

MTF11A

007-503

MTF11A

011-503

MTF11A

015-503

MTF11A

022-503

MTF11A

030-503

MTF11A

040-503

Size 1

Size 2

Apparent output power at
V

Mains

= AC 380-500 V

Rated

1.1 kVA

1.4 kVA

1.8 kVA

2.2 kVA

2.8 kVA

3.8 kVA

5.1 kVA

6.7 kVA

Supply voltages
Permitted range

Mains

AC 3 x 380 V / 400 V / 415 V /

460 V

/ 500 V

Mains

= AC 380 V –10% – AC 500 V +10%

Supply frequency

Mains

50-60 Hz ± 10%

Rated mains current
(with V

Mains

= AC 400 V)

Mains

AC 1.1 A

AC 1.4 A AC 1.7 A AC 2.1 A

AC 3.0 A AC 4.3 A

AC 5.8 A

AC 6.9 A

Output voltage

Output

0 – V

Mains

Output frequency
Resolution
Operating point

2-120 Hz
0.01 Hz
400 V at 50 Hz / 100 Hz

Rated output current

Rated

AC 1.6 A

AC 2.0 A AC 2.5 A

AC 3.2 A

AC 4.0 A AC 5.5 A

AC 7.3 A AC 8.7 A

Motor power S1

Mot

0.37 kW

0.5 HP

0.55 kW

0.75 HP

0.75 kW

1.0 HP

1.1 kW

1.5 HP

1.5 kW

2.0 HP

2.2 kW

3.0 HP

3.7 kW

5.0 HP

4.0 kW

5.4 HP

PWM frequency

4/8/

kHz (

factory setting 16 kHz

)

1) 16 kHz PWM frequency (low-noise): The unit switches to lower cycle frequencies depending on the heat sink temperature and load.

Current limitation

max

motor:

160% at

and

regenerative:

160% at

and

External braking resistor

min

150

Cable length between
MOVIFIT

and motor

Max. 15 m (with SEW hybrid cable, type A)

Hybrid cable shielding

Apply outer shield with EMC cable gland; apply inner shield with EMC shield clamp
(see section "Installation Instructions").

Interference immunity

Fulfills EN 61800-3

Interference emission

Limit value class C3 to EN 61800-3

Motor protection

Thermistor

Operating mode

S1 (EN 60034-1), S3 max. cycle duration 10 minutes

Cooling type (DIN 41751)

Self-cooling

Degree of protection

Standard:
IP65 in accordance with EN 60529 (MOVIFIT

housing closed and all cable bushings and

plug connections sealed)
Hygienic

plus

version:

IP66 in accordance with EN 60529 and IP69K in accordance with DIN 40050-9 (MOVIFIT

housing closed and all cable bushings sealed according to the relevant degree of protection)

Ambient temperature

–25°C to +40°C (P

Rated

reduction: 3% I

Rated

per K to max. 60°C)

Climate class

EN 60721-3-3, class 3K3

Storage temperature

2) If the unit is being stored for a long time, connect it to the mains voltage for at least 5 minutes every 2 years. Otherwise, the unit's

service life may be reduced.

–25°C to +85°C (EN 60721-3-3, class 3K3)

Permissible oscillation and
impact load

According to EN 50178

Overvoltage category

III according to IEC 60664-1 (VDE 0110-1)

Pollution class

2 according to IEC 60664-1 (VDE 0110-1) within the housing

Installation altitude

Up to 1,000 m without restrictions
(installation altitude at 1000 m and higher: see section "Installation instructions")

Mass

EBOX "MTF...-....-00" (MOVIFIT

-FC) size 1: Approx. 3.5 kg

EBOX "MTF...-....-00" (MOVIFIT

-FC) size 2: Approx. 5.6 kg

ABOX "MTA...-S02.-...-00": Approx. 4.5 kg
ABOX "MTA...-S42.-...-00", "MTA...-S52.-...-00", "MTA...-S62.-...-00": Approx. 4.8 kg
ABOX "MTA...-H12.-...-00", "MTA...-H22.-...-00": Approx. 6.0 kg

kVA

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 132 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: