SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 125

Страница: 125 / 172

Operation

Manual operation using the DBG keypad

Operating Instructions – MOVIFIT

-FC

125

7.2

Manual operation using the DBG keypad

7.2.1

Connection

MOVIFIT

units have an X50 (RJ10 plug connector) diagnostic interface for parameter

setting and manual operation.
The X50 diagnostic interface is located under the cable gland shown in the following
figure:

You can also connect the DBG keypad to the MOVIFIT

unit using option DKG60B (5 m

extension cable).

7.2.2

Operation

793024907

DBG

DKG60B

WARNING

The surfaces of MOVIFIT

and of the external options, for example, the braking

resistor, can reach high temperatures during operation.
Danger of burns
• Do not touch MOVIFIT

or the external options until they have cooled down

sufficiently.

NOTICE

The degree of protection specified in section Technical Data only applies if the screw
plug of the diagnostic interface is mounted correctly.
A missing or incorrectly installed screw plug can cause damage to MOVIFIT

• Make sure the screw plug has a seal after manual operation and then screw in the

plug.

TIP

For notes on operating MOVIFIT

in manual operation, refer to the "MOVIFIT

Function Level "Technology"..." or "MOVIFIT

Function Level "Classic"..." manual.

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 125 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: