manualshive.com logo in svg

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 122 / 172

Поделиться
Скачать
SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 122

7

Operation

Status LEDs for MOVIFIT®-FC

122

Operating Instructions – MOVIFIT

®

-FC

7.1.6

"RUN PS" LED (frequency inverter status LED)

The following figure shows the "RUN PS" LED (shown unlit). In the sample figure, the
PROFIBUS versions are shown in the "Technology" or "System" function level:

836134539

LED 
color

LED status

Operating state

Description

-

Off

Not ready

No 24 V power supply

Yellow

Flashing steadily

Not ready

Self-test phase is active or 24 V supply is present 
but the mains voltage is not OK.

Yellow

Flashing evenly, 
fast

Ready for operation Brake release without drive enable is active.

Yellow

Constantly lit

Ready, 
but unit inhibited

24 V power supply and supply voltage OK, 
but no enable signal.

Green/
yellow

Flashing with 
alternating colors

Ready, 
but timeout

Faulty communication with cyclical data exchange

Green

Constantly lit

Unit enabled

Motor in operation

Green

Flashing evenly, 
fast

Current limit active

Drive operating at current limit.

Green

Flashing steadily

Ready for operation Standstill current function active

Red

Constantly lit

Not ready

Check 24 V supply. Make sure that a smoothed 
DC voltage with low ripple is present (residual 
ripple max. 13 %).

Red

2x flashing, break

Fault 07

DC link voltage too high.

Red

Flashing slowly

Fault 08

Speed monitoring error

Fault 09

Incorrect startup/parameter settings

Fault 90

Incorrect assignment of motor to inverter 
Invalid DIP switch settings

Fault 15

24 V supply voltage too low

Faults 17-24, 37

CPU fault

Fault 25

EEPROM fault

Fault 26

Fault at external terminal (only at slave unit)

Fault 94

Checksum error

Fault 97

Copy error

Red

3x flashing, break

Fault 01

Overcurrent in output stage

Fault 11

Overtemperature in output stage

Red

4x flashing, break

Fault 84

Overload in motor

Fault 31

TF was triggered.

Red

5x flashing, break

Fault 89

Overtemperature in brake
Incorrect assignment of motor-frequency inverter

Fault 4

Overcurrent in brake chopper

Red

6x flashing, break

Fault 06

Mains phase failure 

Fault 81

Start condition (only in hoist operation mode)

Fault 82

Open output 

DI03

DI01DI02

DI00

DI04DI05DI06DI07

DI08DI09DI10DI1

1

DI12/DO0

0

DI13/DO01

DI14/DO0

2

DI15/DO0

3

SF/USR

BUS-F

24V

-C

24V

-S

RUN

RUN PS

MOVIFIT

®

Содержание MOVIFIT-FC













































































































































































Отзывы:

Нет отзывов