SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 115

Страница: 115 / 172

Operation

Status LEDs for MOVIFIT®-FC

Operating Instructions – MOVIFIT

-FC

115

"PIO" LED

The "PIO" LED checks the polled I/O connection (process data channel).
The functionality is described in the following table.

PIO

Status

Meaning

Remedy

Flashing
green
(500 ms
cycle)

DUP-MAC
check

•

Unit is performing DUP-MAC check.

•

If the station does not leave this status
after about 2 seconds, it means that no
further stations were found.

•

Activate at least one other
DeviceNet station in the
network.

Off

Not switched
on/Offline but
not DUP-MAC
check

•

Unit is switched off.

•

Unit is in offline status.

•

Switch on the unit.

•

Check whether the PIO
connection type in the
master was activated.

Flashing
green
(1 s
cycle)

Online and in
operational
mode

•

Unit is online.

•

DUP-MAC check performed success-
fully

•

A PIO connection is being established
with a master (configuring state).

•

Missing, incorrect or incomplete
configuration

•

Check the unit configura-
tion in the master.

Green

Online, opera-
tional mode
and connected

•

Unit is online.

•

A PIO connection has been established
(established state).

Flashing
red
(1 s
cycle)

Minor fault or
connection
timeout

•

A correctable fault has occurred.

•

Invalid baud rate set at the DIP
switches.

•

Polled I/O connection is in timeout
status.

•

Check the DeviceNet
cable.

•

Check the position of DIP
switches for the baud rate.

•

Check the timeout
response (P831). If a
response with fault is set,
reset the unit once the fault
has been corrected.

Red

Critical fault or
Critical link
failure

•

A fault that cannot be corrected has
occurred.

•

Bus off status

•

DUP-MAC check has detected a fault.

•

Check the DeviceNet
cable.

•

Check the slave address
(MAC ID). Is another unit
already using the same
address?

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 115 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: