SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 113

Страница: 113 / 172

Operation

Status LEDs for MOVIFIT®-FC

Operating Instructions – MOVIFIT

-FC

113

7.1.2

Bus-specific LEDs for PROFIBUS

This section describes the bus-specific LEDs for PROFIBUS. In the following figure, the
LEDs are shown as dark:

"BUS-F" LED

The following table shows the statuses of the "BUS-F" LED:

"RUN" LED

The following table shows the statuses of the "RUN" LED:

836104971

DI03

DI01DI02

DI00

DI04DI05DI06DI07

DI08DI09DI10DI1

DI12/DO0

DI13/DO0

DI14/DO0

DI15/DO0

SF/USR

BUS-F

24V

-C

24V

-S

RUN

RUN PS

MOVIFIT

BUS-F

RUN

Meaning

Remedy

Off

Green

MOVIFIT

is currently exchanging data

with the DP master (data exchange).

Flashing
red

Green

•

The baud rate is detected. However,
MOVIFIT

is not being addressed

by the DP master.

•

MOVIFIT

was configured

incorrectly or not configured in
DP master.

•

Check configuration of the DP master.

•

Check whether all the modules config-
ured during project planning are per-
mitted for the MOVIFIT

variants

(MC, FC, and SC).

Red

Green

•

Connection to the DP master has
failed.

•

MOVIFIT

does not detect baud rate.

•

Bus interruption

•

DP master not in operation

•

Check the PROFIBUS DP connection
of MOVIFIT

•

Check the DP master.

•

Check all cables in your PROFIBUS
DP network.

BUS-F

RUN

Meaning

Remedy

Off

•

MOVIFIT

not ready for operation

•

No 24 V power supply

•

Check DC 24 V supply.

•

Switch on MOVIFIT

again. Exchange

EBOX if problem occurs repeatedly.

Green

MOVIFIT

components hardware OK

Off

Green

•

MOVIFIT

operating correctly.

•

MOVIFIT

is currently exchanging

data with the DP master (data
exchange) and all subordinate
drive systems.

Flashing
green

PROFIBUS address is set equal to 0 or
higher than 125.

Check the PROFIBUS address set in the
MOVIFIT

-ABOX.

Yellow

MOVIFIT

is currently being initialized.

Red

Internal unit fault

Switch on MOVIFIT

again. Exchange

EBOX if problem occurs repeatedly.

Any status

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 113 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: