SEW-Eurodrive MOVIFIT-FC Скачать руководство пользователя страница 112

Страница: 112 / 172

Operation

Status LEDs for MOVIFIT®-FC

112

Operating Instructions – MOVIFIT

-FC

"SF/USR" LED

The "SF/USR" LED indicates the various statuses depending on the function level.
The following table shows the statuses of the "SF/USR" LED:

SF/USR

Function

level

Meaning

Remedy

Off

•

Standard operating state:
MOVIFIT

exchanges data with

the connected drive system
(integrated inverter).

Red

•

MOVIFIT

cannot exchange

data with an integrated inverter.

Check the DC 24 V supply of the integrated
inverter.

Flashing
red
(2 s
cycle)

•

MOVIFIT

initialization error or

serious unit fault

Incorrect card ID
Switch on MOVIFIT

again. If the fault is still

present, replace the EBOX or contact SEW
Service.

Flashing
red

•

Other unit faults

Use MOVITOOLS

MotionStudio to read out

the fault status.
Remedy the cause of and acknowledge the
fault.

Off

•

IEC program is running.

Green

•

IEC program is running.
The IEC program controls the
green LED.

For the meaning, see the IEC program
documentation.

Red

•

Due to an error, boot project was
cancelled or did not start.

Use MOVITOOL

/PLC Editor/Remote Tool to

log on; start the boot project.

•

MOVIFIT

initialization fault

Incorrect EBOX/ABOX combina-
tion

Incorrect card ID
Check the type of MOVIFIT

-EBOX. Place

the correct EBOX in the ABOX and perform
the complete startup process.

Flashing
red

•

No IEC application program
loaded

Load an IEC application program and, if
necessary, restart the integrated PLC.

Flashing
yellow

•

The IEC application program
has been loaded, but it is not
running (PLC = Stop).

Check the IEC application program using
MOVITOOLS

MotionStudio and, if neces-

sary, restart the integrated PLC.

Flashing
1 x red
and
n x
green

•

Fault status reported by the IEC
program

For status/rectification, see the IEC program
documentation.

Red

•

MOVIFIT

displays a fault

status.

Eliminate the cause of the fault and use
PROFIBUS to acknowledge the fault mes-
sage. Use MOVIVISION

for detailed fault

diagnostics.

Flashing
red

•

MOVIFIT

indicates a fault

status; cause of fault has
already been eliminated.

Use PROFIBUS to acknowledge the fault
message. Use MOVIVISION

for detailed

fault diagnostics.

•

Valid for selected function level:
C = Function level "Classic"
T = Function level "Technology"
S = Function level "System"

Содержание MOVIFIT-FC













































































































































































Результаты поиска

Содержание MOVIFIT-FC

Отзывы:

SEW-Eurodrive MOVIFIT-FC, Руководство по эксплуатации, Страница: 112 / 172

Результаты поиска

Содержание MOVIFIT-FC

Отзывы: