manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Скачать руководство пользователя страница 45

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card 

45

6

Introduction to PROFIBUS DP-V1

DP-V1 Functions

6

DP-V1 Functions

6.1

Introduction to PROFIBUS DP-V1

This section describes the functions and terms used for operating the DHP11B control
card on PROFIBUS DP-V1. Refer to the PROFIBUS user organization or visit
www.profibus.com for detailed technical information on PROFIBUS DP-V1.

The PROFIBUS DP-V1 specification introduced new acyclical 

read/write

 services within

the context of the PROFIBUS DP-V1 expansions. These acyclical services are inserted
in special telegrams during ongoing cyclical bus operation to ensure compatibility be-
tween PROFIBUS DP (version 0) and PROFIBUS DP-V1 (version 1).

The acyclical 

read/write

 services can be used to exchange larger volumes of data be-

tween master and slave (DHP11B control card) than it would be possible to transfer with
the cyclical input or output data via the 8-byte parameter channel. The advantage of the
acyclical data exchange via DP-V1 is the minimum load on the cyclical bus operation.
DP-V1 telegrams are only added to the bus cycle if required.

The DP-V1 parameter channel offers the following options:

•

The higher-level controller can access all the device information of the SEW DP-V1
slaves. This means that cyclical process data and unit settings can be read, stored
in the higher-level controller and modified in the slave.

•

It is also possible to route the MOVITOOLS

®

 service and startup tool via the DP-V1

parameter channel instead of using a proprietary RS485 connection. Once you have
installed the MOVITOOLS

®

 MotionStudio software, you can access detailed informa-

tion in the folder ...\SEW\...

The main features of PROFIBUS DP-V1 are shown in the figure below.

20068AXX

Acyclic DP1-V1

C1-Services

C1-Master

C2-Master

C2-Master

PROFIBUS DP-V1

Acyclic DP1-V1

C2-Services

Acyclic DP1-V1

C2-Services

PD

PD

Param

Param

Cyclic OUT Data

MOVI-

PLC

0

0

I

Содержание MOVIDRIVE MOVI-PLC DHP11B

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды