manualshive.com logo in svg

SEW-Eurodrive MOVI-PLC basic DHP11B-T0, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-PLC basic DHP11B-T0 Скачать руководство пользователя страница 11

2

Introduction

OST11B option

Manual – MOVI-PLC

®

 basic DHP11B.. controller

11

Binary inputs and 
outputs

Binary inputs and outputs enable you to switch actuators, (e.g. valves) and evaluate
binary input signals (e.g. sensors). You can freely use the binary inputs and outputs in
the PLC Editor of the MOVITOOLS

®

 MotionStudio software in programming.

Diagnostics

The seven LEDs of MOVI-PLC

®

 

basic 

DHP11B.. controller indicate the following states:

• Voltage supply of the binary inputs and outputs (LED 1)
• General status of the MOVI-PLC

®

 

basic 

DHP11B.. controller (LED 2)

• Status of the control program (LED 3)
• Status of the PROFIBUS interface (LED 4, 5)
• Status of the two CAN interfaces (LED 6, 7)
You can connect operator terminals to perform diagnostics. It is recommended to
connect an operator terminal to RS485. Connection to interfaces CAN 1 or CAN 2 is in
preparation.

2.3

OST11B option

Features

In conjunction with MOVI-PLC

®

 

basic 

DHP11B.. controller, the OST11B option offers

you a further RS485 interface COM2 in terminal design or as an engineering interface
(RJ10-socket).

RS485 interface 
COM2

Connect one of the following devices to the RS485 interface COM2:
• Engineering PC, or
• DOP11A operator terminal, or
• Gearmotor with integrated frequency inverter MOVIMOT

®

Diagnostics

An LED indicates correct connection to the MOVI-PLC

®

 

basic 

DHP11B.. controller.

Содержание MOVI-PLC basic DHP11B-T0

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды