SEW-Eurodrive MOVI-C UHX65A-M Скачать руководство пользователя страница 38

Страница: 38 / 60

EtherNet/IP™ networks – Recommendations

Network components

Manual – MOVI-C

CONTROLLER progressive UHX65A-M

EtherNet/IP™ networks – Recommendations

The Ethernet Industrial Protocol (EtherNet/IP™) is an open communication standard
based on the conventional Ethernet protocols TCP/IP and UDP/IP.

EtherNet/IP™ has been defined by the

pen

eviceNet

endor

ssociation (ODVA)

and

ontrolNet

nternational (CI).

EtherNet/IP™ extends the Ethernet technology by the CIP application protocol (

om-

mon

ndustrial

rotocol). CIP is known in the field of automation engineering because

it is also used as an application protocol for DeviceNet™ and ControlNet™.

INFORMATION

Adhere to the information and regulations of the ODVA when planning your EtherNet/
IP™ network and taking it into operation.

This chapter describes the most important conditions to be observed for planning and
operating an EtherNet/IP™ network. The list is not complete.

9.1

Network components

Observe the following when selecting the network components for an EtherNet/IP™
network:

•

Use only industry-standard network components.

•

Use industry-standard switches.

•

Use fast Ethernet according to IEEE802.3u.

•

The managed switch must support VLAN tagging according to IEEE802.1Q.

9.2

Maximum line depth

It is recommended to use a maximum of 50 fieldbus nodes in a line regardless of the
poll rate.

9.3

Network load

The network load should not exceed 80% of the bandwidth at any point in the network.

26881144/EN – 02/2022

Содержание MOVI-C UHX65A-M





























































Результаты поиска

Содержание MOVI-C UHX65A-M

Отзывы:

SEW-Eurodrive MOVI-C UHX65A-M, Руководство пользователя, Страница: 38 / 60

Результаты поиска

Содержание MOVI-C UHX65A-M

Отзывы: