manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 41

4

Installation notes

Terminal assignment

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

41

4.4

Terminal assignment

INFORMATION

Reference potentials inside the device:

The device internal reference potential is designated as GND in the following table.

All reference potentials GND are internally connected to PE.

INFORMATION

The assignment "reserved" means that no cable must be connected to this connec-
tion.

Represent-
ation

Terminal

Connection

Short description

GND

24V

X5:24V

V

I

24 V

DC 24 V supply voltage

X5:GND

GND

Reference potential

1

8

X30

Fast system bus SBus

PLUS

 based on EtherCAT

®

10/100 BaseT

1000 BaseT

10/100 BaseT

1000 BaseT

1

8

X80/X81:1

TX+

DA+

Transmit line (+)

Bidirectional pair A

X80/X81:2

TX-

DA-

Transmit line (-)

Bidirectional pair A

X80/X81:3

RX+

DB+

Receive line (+)

Bidirectional pair B

X80/X81:4

Reserved

DC+

–

Bidirectional pair C

X80/X81:5

Reserved

DC-

–

Bidirectional pair C

X80/X81:6

RX-

DB-

Receive line (-)

Bidirectional pair B

X80/X81:7

Reserved

DD+

–

Bidirectional pair D

X80/X81:8

Reserved

DD-

–

Bidirectional pair D

1

8

X40/X41:1

TX+

Transmit line (+)

X40/X41:2

TX-

Transmit line (-)

X40/X41:3

RX+

Receive line (+)

X40/X41:4

Reserved

–

X40/X41:5

Reserved

–

X40/X41:6

RX-

Receive line (-)

X40/X41:7

Reserved

–

X40/X41:8

Reserved

–

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды