SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 38

Страница: 38 / 92

Installation notes

Electrical installation

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

4.3.5

EtherCAT

/SBus

PLUS

master connection

The MOVI-C

CONTROLLER serves as EtherCAT

/SBus

PLUS

master for the lower-

level application inverters (EtherCAT

/SBus

PLUS

slaves). The communication takes

place via the EtherCAT

-based, fast system bus SBus

PLUS

(terminal X30).

EtherCAT

/SBus

PLUS

bus topology

EtherCAT

/SBus

PLUS

is designed for linear bus structure with RJ45 connectors. The

EtherCAT

/SBus

PLUS

slave devices are connected via a shielded twisted-pair cable.

X30

X31

L/A

US1

L/A

X45A-

[1]

[2]

[3]

[4]

9007220482503307

[1] System bus cable, 4-pin, color: light gray
[2] Module bus cable, 8-pin, color: anthracite gray
[3] MOVIDRIVE

modular

[4] MOVI‑C

CONTROLLER (master module)

INFORMATION

According to IEEE 802.3, 200 Edition, the maximum cable length for
10 MBaud/100 MBaud Ethernet (10BaseT/100BaseT) between 2 EtherCAT

SBus

PLUS

stations is 100 m.

Bus termination

Bus termination (for example with bus terminating resistors) is not necessary. The sys-
tem detects automatically if there is no subsequent device connected to a device.

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды