manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 22

4

Installation notes

Mechanical installation

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

22

4.2.2

Control cabinet installation

Control 

cabinet 

installation 

is 

shown 

at 

an 

axis 

system 

with 

a

MOVI‑C

®

  CONTROLLER,  a  power  supply  module  and  several  axis  modules.  The

MOVI‑C

®

  CONTROLLER  can  either  be  used  as  compact  controller  or  as  master

module.

Alignment in the axis system

When arranging the axis system, observe that the nominal output current I

N

 of the axis

modules  must  decrease  from  left  to  right.  The  axis  module  with  the  highest  nominal
output  current  must  be  on  the  right  side  of  the  power  supply  module.  All  remaining
axis modules are installed in descending order regarding their nominal output current.

When used as master module (see figure), as well as when used as compact control-
ler,  MOVI-C

®

  CONTROLLER  must  always  be  installed  left  of  the  power  supply

module.

In one axis system, up to 15 axis modules can be used, both as single-axis modules
and double-axis modules.

80

/A

X5

X30

X31

L/A

L/A

1

2

3

4

1

3

85

US1

BF

L/A

X4

0

L/A

UH

X45A-

N

X4

1

5

6

XM

[1]

[2]

[3]

21042940939

[1]

MOVI‑C

®

 CONTROLLER

[2]

Power supply module

[3]

Axis module sizes 1

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды