SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 21

Страница: 21 / 92

Installation notes

Mechanical installation

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

4.2

Mechanical installation

CAUTION

Risk of injury to persons and damage to property.

Never install a defective or damaged MOVI-C

CONTROLLER.

•

Before installation, check the device for external damage. Replace any damaged
device.

NOTICE

Risk of damage to property due to mounting surface with poor conductivity.

Damage to the MOVI‑C

CONTROLLER.

•

The mounting plate in the control cabinet must be conductive over a large area
for the mounting surface of the MOVI‑C

CONTROLLER (metallically pure, good

conductivity). EMC‑compliant installation of the device can only be accomplished
with a mounting plate that is conductive over a large area.

NOTICE

Risk of damage to property due to non-compliance with the stipulated tightening
torques.

Damage to the MOVI‑C

CONTROLLER.

•

Always adhere to the stipulated tightening torques. Otherwise, excessive heat
can develop which would damage the device.

4.2.1

Minimum clearance and mounting position

MOVI‑C

CONTROLLER is installed in the control cabinet. Observe the following for

installation:

•

To ensure unobstructed cooling of the MOVI-C

CONTROLLER, leave a minimum

clearance of 100 mm above and below the device's housing. Make sure air circula-
tion in the clearance is not impaired by cables or other installation equipment.

•

Ensure

unobstructed

cooling

air

supply

and

make

sure

that

the

MOVI‑C

CONTROLLER is not exposed to the warm exhaust air from other

devices.

•

There is no need for clearance at the sides of the device. You may connect the
MOVI‑C

CONTROLLER and other devices (e.g. MOVIDRIVE

modular) in series.

•

Install the devices only vertically. You must not install them horizontally, tilted or
upside down.

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды