manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 12

2

Safety notes

Electrical installation

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

12

2.8

Electrical installation

Ensure that all of the required covers are correctly attached after carrying out the elec-
trical installation.

Make  sure  that  preventive  measures  and  protection  devices  comply  with  the  applic-
able regulations (e.g. EN 60204-1 or EN 61800-5-1).

2.8.1

Required preventive measure

Make sure that the product is correctly attached to the ground connection.

2.9

Bus systems

A bus system makes it possible to adapt electronic drive components to the particulars
of  the  machinery  within  wide  limits.  There  is  a  risk  that  a  change  of  parameters  that
cannot be detected externally may result in unexpected (but not uncontrolled) system
behavior and may have a negative impact on operational safety, system availability, or
data security.

Especially  in  Ethernet-based  networked  systems  and  with  engineering  interfaces,
make sure that unauthorized access is prevented.

Use IT‑specific safety standards to increase access protection to the ports. For a port
overview, refer to the respective technical data of the device in use.

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды