manualshive.com logo in svg

SEW-Eurodrive IPOS plus, Руководство пользователя


Поделиться
Скачать
background image

Manual – IPOSplus® 

45

5

Interrupts

Task Management and Interrupts

5.4.4

Example

MOVIDRIVE

®

 B positions a travel drive. A PLC controls MOVIDRIVE

®

 via a fieldbus.

Change the individual parameters directly on MOVIDRIVE

®

 using SEW keypads.

Proposed solution:

Task 1: Programming the motion sequence

Task 2: HMI communication with the operator terminal

Task 3: Fieldbus communication with the PLC

It is important to distribute the additional commands correctly, depending on the appli-
cation:

•

Interrupt-oriented programs:

When a user program is interrupt-oriented and the

task 1 interrupts should be processed quickly, task 1 must be assigned a high
calculation priority using additional commands in P938.

•

Runtime-optimized programs:

If, for example, process data is to be converted in

IPOS, this must be done as quickly as possible. Task 3 can be used to process
convert routines as quickly as possible. In this case, task 1 and task 2 should be
assigned as few additional commands/ms as possible. This ensures the fastest total
application performance if tasks 1 and 2 run with the minimum speed.

5.5

Interrupts

An interrupt - triggered by an event - interrupts the processing of the task it is assigned
to. The entire interrupt routine is run through once, as long as it is not interrupted by an
interrupt with a higher priority of the same task. 

An interrupt that is activated by _SetInterrupt() or SETINT can be triggered by a timer0
overflow, a system/unit fault or touch probe DI02 and interrupts task 1. 

In MOVIDRIVE

®

 B, up to 4 additional variable interrupts can be activated using

_SetVarInterrupt() or VARINT. They interrupt task 2 or task 3 as required.

The response time for task 1 interrupts (unit fault, DI02 touch probe or T0_overflow) is
dependent on the number of activated interrupts (1 interrupt <= 1ms, 2 interrupts <=
2ms, 3 interrupts <= 3ms). The response time for variable interrupts is dependent on the
number of activated interrupts <= 1ms. 

If an interrupt is triggered during a wait command, the waiting time of the command con-
tinues to run in the background. Once the program has jumped back to the task, it only
has to wait the remaining time before continuing. 

P

i

f

kVA

Hz

n

P

i

f

kVA

Hz

n

Содержание IPOS plus

































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IPOS plus

ZKTeco SC800 Quick Start Manual preview
SC800
Бренд: ZKTeco Страницы: 18
NEC N8403-019 User Manual preview
N8403-019
Бренд: NEC Страницы: 146
B&R Industries AP1000 User Manual preview
AP1000
Бренд: B&R Industries Страницы: 89
Bard ECU Series Advanced Programming & Features preview
ECU Series
Бренд: Bard Страницы: 8
Bardiani Valvole B925 Use And Maintenance Manual preview
B925
Бренд: Bardiani Valvole Страницы: 35
Danfoss VLT series Quick Manual preview
VLT series
Бренд: Danfoss Страницы: 37
Daikin MicroTech II Operation And Maintenance Manual preview
MicroTech II
Бренд: Daikin Страницы: 44
VCON Escort Installation And Setup Manual preview
Escort
Бренд: VCON Страницы: 66
E-T-A EtherNetIP ControlPlex CPC12EN User Manual preview
EtherNetIP ControlPlex CPC12EN
Бренд: E-T-A Страницы: 28
LaserBit LB Series User Manual preview
LB Series
Бренд: LaserBit Страницы: 69
Lawler 805 Installation & Maintenance Manual preview
805
Бренд: Lawler Страницы: 5
IFM Electronic Ecomot300 AC2630 Supplementary Device Manual preview
Ecomot300 AC2630
Бренд: IFM Electronic Страницы: 111
Parker CHELSEA Owner'S Manual preview
CHELSEA
Бренд: Parker Страницы: 32
Rayrun NT30 Quick Start Manual preview
NT30
Бренд: Rayrun Страницы: 4
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Бренд: PACH & COMPANY Страницы: 2
vacuubrand CVC 3000 Instructions For Assembly preview
CVC 3000
Бренд: vacuubrand Страницы: 12
Vacon 100 INDUSTRIAL Installation And User Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 47
VADDIO ConferenceSHOT AV Complete Manual preview
ConferenceSHOT AV
Бренд: VADDIO Страницы: 114

Бренды по названию

Популярные бренды

Загрузить еще бренды