SEW-Eurodrive DR63 Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

SEW-Eurodrive DR63 Series Скачать руководство пользователя страница 22

22

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280

4

Painting

Mechanical Installation

4.6.2

Tightening torques

The following table shows all the tightening torques required for this procedure:

4.7

Painting

WARNING

Possible damage to the motor outputs when turning the terminal board.

Possible damage to property.
• To make sure that the cables have not been damaged, carry out an insulation test

after re-assembly, see chapter "Extended storage of motors" (page 17).

Key num-
ber

Screw

Applies to

Tightening torque
in Nm

in lb-in

[2]

Terminal stud nut

M6 stud

3

26.6

M8 stud

6

53.1

M12 stud

15.5

137.2

[61]

Pan head screw option terminal

EDR.71 – 225

1.8

16.0

[113]

Pan head screw DIN rail connection

EDR.71 – 132

5

44.3

[117]

Hexagon screw grounding inside

EDR.71 – 132

4

35.4

EDR.160

25.5

225.7

EDR.180 – 225 (alumi-
num design)

25.5

225.7

EDR.180 – 225 (gray-
cast iron design)

50

442.5

[119]

Pan head screw of terminal box

EDR.71 – 132

5

44.3

EDR.160 – 225

25.5

225.7

[123]

Hexagon screw terminal box cover

EDR.71 – 132

4

35.4

EDR.160

10.3

91.2

EDR.180 – 225 (alumi-
num design)

10.3

91.2

EDR.180 – 225 (gray-
cast iron design)

25.5

225.7

[140]

Hexagon screw grounding outside

EDR.71 – 225

4

35.4

[a1]

Screw of option terminal / rectifier

EDR.71 – 225

1.8

16.0

[a2]

Flat head screw option terminal

EDR.71 – 225

1

8.9

NOTE ON EXPLOSION PROTECTION

SEW-EURODRIVE delivers the drives with a painting that complies with the require-
ments for preventing electrostatic charging according to EN / IEC 60079-0. If you re-
paint the motors or gearmotors, observe the requirements for preventing electrostatic
charging according to EN 60079-0.

«
...
20
21
22
23
24
...
»

Содержание DR63 Series

































































Отзывы:

Нет отзывов