manualshive.com logo in svg

SEW-Eurodrive DR63 Series, Дополнение к инструкции по эксплуатации, Страница: 16 / 64

Поделиться
Скачать
SEW-Eurodrive DR63 Series Скачать руководство пользователя страница 16

16

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280

4

Before you start

Mechanical Installation

4

Mechanical Installation

4.1

Before you start

Install the drive only if the following conditions are met:

• The data on the nameplate of the drive corresponds with the voltage supply system

or with the output voltage of the frequency inverter

• The drive is undamaged (no damage caused by transport or storage)

• All transport locks have been removed. 

• You are certain that the following requirements have been met:

– Ambient temperature between -20

˚

C and +40 °C. 

Note that the temperature range of the gear unit may also be restricted (see gear
unit operating instructions).

Any differing specifications on the nameplate must be observed. The ambient
conditions must comply with all the specifications on the nameplate.

– No oils, acids, gases, vapors, dusts, radiations, etc.

– Max. installation altitude 1000 m above sea level.

Observe chapter "Electrical Installation" > "Ambient conditions during operation"
> "Installation altitude".

– Note the restrictions for encoders.

– Special design: The drive is designed in accordance with the ambient conditions

The above mentioned information refers to standard orders. The conditions might be dif-
ferent when you order drives other than the standard. Refer to the order confirmation for
differing conditions. 

INFORMATION

It is essential that you observe the safety notes in chapter 2 for mechanical installation.

NOTICE

The mounting position for installation must correspond with the specifications on the
nameplate.

Содержание DR63 Series

































































Отзывы:

Нет отзывов