manualshive.com logo in svg

SEW-Eurodrive CMP40, Руководство по эксплуатации

Поделиться
Скачать
SEW-Eurodrive CMP40 Скачать руководство пользователя страница 48

48

Operating Instructions – Explosion-Proof CMP Synchronous Servomotors

10 

Brake 

Technical Data 

10.4 Brake

The mechanical brake is a holding brake implemented as a spring-loaded brake.
The brake has a standard supply voltage of DC 24 V and operates with 1 or 2 braking
torque ratings for each motor size (CMP40, CMP50 and CMP63). 
The brake cannot be retrofitted and operates without brake rectifier or brake control unit. 
If the servomotors are run on inverters from SEW-EURODRIVE, overvoltage protection
is provided.
If the servomotors are run on non-SEW-inverters, overvoltage protection must be imple-
mented by the customers themselves using, for example, varistors.
Observe the notes in the relevant operating instructions for servo controllers concerning
the switching sequence of motor enable and brake control during standard operation.

10.4.1 Speed ratings

The BP brake can be used for the following rated speeds:

10.4.2 Basic structure of the BP holding brake for CMP40/50/63

Servomotor

Rated speed

CMP40

3000 / 4500

CMP50

3000 / 4500

CMP63

3000 / 4500

55832AXX

Figure 1: Principle structure of the 24 V spring-loaded BP

[1]

Carrier

[2]

Complete brake

[1]

[2]

P

i

f

kVA

Hz

n

Содержание CMP40

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды