manualshive.com logo in svg

SEW-Eurodrive CMP40, Руководство по эксплуатации

Поделиться
Скачать
SEW-Eurodrive CMP40 Скачать руководство пользователя страница 41

Operating Instructions – Explosion-Proof CMP Synchronous Servomotors  

41

9 

Brake malfunctions

Inspection/Maintenance

9

Inspection/Maintenance

Only SEW service staff, repair workshops or plants that have the necessary expertise
may repair or modify the servomotor. 
Before re-startup of the servomotor, make sure that all regulations are complied with and
document this with a label on the servomotor or a written test report. 

NOTE ON EXPLOSION PROTECTION

• Maintenance and repair work must always be performed by SEW-EURODRIVE or

repair workshops for electrical drives. 

• Use only original spare parts from the relevant and valid spare parts lists; otherwise,

the explosion-poof approval for the servomotor will become void.

• The routine test must be repeated whenever motor parts relating to explosion pro-

tection are replaced.

• Servomotors can become very hot during operation – danger of burns!
• Isolate the servomotor and brake from the power supply before starting work, safe-

guarding them against unintentional re-start!

• Drive must be shut down safely for the duration of the maintenance work, since ro-

tation will energize the motor terminals.

• Ensure that the servomotor is assembled correctly and all openings have been

plugged after service and maintenance work.

• Clean servomotors in explosion-proof areas regularly. Prevent dust deposits > 5

mm.

• Explosion protection is largely dependent on the IP enclosure. Therefore, always

check that the seals are fitted correctly and in perfect condition when performing any
work on the machine.

• Apply grease with a grease depot (Klüber Patemo GHY133N) to the lip of the oil

seal before assembly.

• Always perform safety and functional tests following all maintenance and repair

work (thermal protection, brake).

• Explosion protection can only be ensured if servomotors and brakes are serviced

and maintained correctly.

Содержание CMP40

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды