Setra Systems DATUM 2000 Скачать руководство пользователя страница 27

Страница: 27 / 28

14.0 "FCC warning"

WARNING:

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

NOTE:

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with the Class

A, Part 15 FCC limits.

Содержание DATUM 2000





























Результаты поиска

Содержание DATUM 2000

Отзывы:

Похожие инструкции для DATUM 2000

Бренды по названию

Популярные бренды

Setra Systems DATUM 2000, Руководство по эксплуатации

Результаты поиска

Содержание DATUM 2000

Отзывы:

Похожие инструкции для DATUM 2000

Бренды по названию

Популярные бренды