background image

23

11.0 DATUM 2000

 manometer specifications

w/Models 204/204D

w/Model 239

w/Model 270

Type of pressure 

measurement

Gage

Absolute

Vacuum

Differential

Differential

Gage

Gage

Absolute

Barometric

Standard ranges

0 to 25, 50, 100, 250, 

500, 1000 psig

0 to 25, 50, 100, 250,  

500, 1000 psia

0 to 25, 50, 100 psid

0 to 14.7 psib

0 to ±10, ±25, ±50, ±100 psid

0 to 0.5, 1.0, 2.5, 5,  

15, 30 inch WC

0 to ±0.25, ±.5,  

±1.0, ±2.5, ±7.5,  

±15 inch WC

0 to 5, 10 psid

0 to ±2.5, ±5 psid

 

0 to 5, 10, 20, 50,  

100 psig

0 to 10, 20, 50,  

100 psia

600-1100 millibar

800-1100 millibar

System accuracy 

(RSS)

±0.11% FS ±2 digits

±0.14% FS ±2 digits

±0.05% FS ± 2 digits

Thermal effects

%FS 60°-95°F

Thermal zero shift

Thermal span shift

0.14 max. ±4 digits

0.11 max. ±4 digits

0.35 max. ±4 digits

0.35 max. ±4 digits

0.07 max. ±4 digits

0.04 max. ±4 digits

Pressure fittings

Positive

Reference

1/4"-18 NPT internal

1/8"-27 NPT internal (204D 

only)

1/8"-27 NPT internal

1/8"-27 NPT internal

1/8"-27 NPT internal

N/A

Pressure media

Positive

Reference

Gas or liquid compatible with 

17-4 PH stainless steel .

Clean dry air or other gases. 

(Non-corrosive, non-

condensible.) Maximum l 

ine pressure 1000 psig  

(204D only)

Gases compatible with 

stainless steel, hard 

anodized 6061 aluminum, 

Buna N O-ring. (Stainless 

steel in place of aluminum 

on special order.

Clean dry air or other gases. 

(Non-corrosive, non-

condensible.) Maximum line 

pressure 250 psig

Dry or wet air, water 

or other media 

compatible with 

aluminum, alumina 

ceramics, gold and 

elastomer sealant.

N/A

Analog output

Normally 0 to 5 VSC for 

unidirectional pressure 

ranges.

0 to ±2.5 VDC for  

bidirectional ranges.

Normally 0 to 5 VDC for 

unidirectional pressure.

0 to ±2.5 VDC for 

bidirectional ranges.

0 to 5 VDC for gage 

and absolute ranges.

(1) Differential pressure models can be used to measure gage pressure by 

leaving the reference port open to atmosphere

(2) Line pressure refers to pressure applied to both high and low sides of the 

sensing device simultaneously. Refer to the product data sheet to determine 

maximum differential pressure and overpressure limits.

Notes:

Содержание DATUM 2000





























Отзывы: