SES SAT2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 19

SES SAT2 Скачать руководство пользователя страница 15

S A T 2 U S E R / I N S T A L L E R G U I D E

Installation of SAT2 (Continued)

Connect the RJ-11 cable to the RJ-11 jack on the SAT2.

Re-Install the door and screw the 6 tamper resistant screws back in the front door.

Press the call button. If the SAT2 has not been programmed, it will give a brief
dial tone, and then hang up. If it has been programmed, it will dial the

programmed phone number.

If the audio needs adjustment, see the following steps on adjusting audio.

Adjusting SAT2 Audio

In most cases, the factory audio adjustment should work fine, but if there are

other circumstances that require adjustment, proceed with care.

The speaker volume and microphone sensitivity interact with each other

An extreme imbalance in adjustment can cause the SAT2 to perform

poorly, or not at all.

Remove the 6 tamper resistant screws with the #15 Tamper Torx

Remove the door assembly.

Press the call button, and while the dial tone is on (it will be on only for a few

seconds), adjust the speaker volume with a 3/32” slotted screwdriver or a slotted

alignment tool. The volume increases in the direction of the arrowhead.

The speaker volume in the SAT2 is only valid while the door assembly is in
the back box, due to resonance. After making any speaker adjustment,

place the door temporarily in the back box and listen again.

To adjust the microphone volume, call some one on the SAT2. After they answer,

start counting and after every three counts or so, adjust the microphone sensitivity

with a 3/32” slotted screwdriver or a slotted alignment tool. The sensitivity

increases in the direction of the arrowhead.

If the sensitivity is too low the called party will not be able to hear you. If
the sensitivity is too high, you will not be able to hear the called party.

Re-Install the door and screw the 6 tamper resistant screws back in the front door.

Installers Note

«
...
13
14
15
16
17
...
»

Содержание SAT2




















Отзывы:

Нет отзывов