Server Technology Switched Rack PDU страница 4 Скачать руководство пользователя

Страница: 4 / 157



Introduction Switched PDU

Installation and Operations Manual

Chapter 1: Introduction

Quick Installation Checklist

The following steps are recommended to quickly install and configure the Switched PDU for use in your data
center equipment cabinet:

Mount the Switched PDU.

Connect to the power source.

Connect the devices.

Connect the sensors.

Connect to the Switched PDU.

Configure the Switched PDU.



Configure the network settings.



Create new administrative user account.



Configure location and Switched PDU names.



Configure sensor names.



Configure new user account(s).



Remove the predefined Administrator account “admn”.

Connect the Switched PDU to the network.

Technical Support

Experience Server Technology's FREE Technical Support

Server Technology



understands that there are often questions when installing and/or using a new product. Free

Technical Support is provided from 8 a.m. to 5 p.m. PST, Monday through Friday. After-hours service is provided to
ensure your requests are handled quickly no matter what time zone or country you are located in.

Server Technology, Inc.

1040 Sandhill Drive

Tel: 1-800-835-1515

Web:

www.servertech.com

Reno, Nevada 89521 USA

Fax: 775-284-2065

Email:

[email protected]

Содержание Switched Rack PDU






























































































































































Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Похожие инструкции для Switched Rack PDU

Бренды по названию

Популярные бренды

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Похожие инструкции для Switched Rack PDU

Бренды по названию

Популярные бренды