manualshive.com logo in svg

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации, Страница: 16 / 157

Поделиться
Скачать
Server Technology Switched Rack PDU Скачать руководство пользователя страница 16

16

 

 Installation                                                                                Switched PDU  

                                                                                                          Installation and Operations Manual 

Attaching the Expansion Module 

Connect the expansion module unit with the provided RJ12 crossover cable at the Link port on the Switched PDU. 

NOTE:

  The overall length of the RJ12 crossover cable should not exceed 10 feet. 

Connecting to the Power Source 

On 30A units, the input power cord is attached to the base of the unit.  On units with a total maximum output <30A, 
you must first attach the power cord to the unit before connecting the unit to the power source. 

To attach a power cord to the unit: 

1.

 

Plug the female end of the power cord firmly into its connector at the base. 

2.

 

Use a screwdriver to tighten the two screws on the retention bracket. 

To connect to the power source: 

Plug the male end of the power cord into the AC power source. 

Connecting Devices 

To avoid the possibility of noise due to arcing: 

1.

 

Keep the device’s on/off switch in the off position until after it is plugged into the outlet. 

2.

 

Connect devices to the PDU outlets.  

NOTE:

  Server Technology recommends even distribution of attached devices across all available outlets to avoid exceeding the outlet, 

branch or phase limitations. 

 

Always disconnect ALL power supply cords before opening to avoid electrical shock. 
Afin d’éviter les chocs électriques, débranchez TOUTES les cables électrique avant d’ouvrir. 

Vor dem Offnen immer Netzleitung abziehen um elektrischen Schlag zu vermeiden.

 

Connecting the Sensors 

The Switched PDU is equipped with two mini RJ11 T/H ports for attachment of the Temperature/Humidity sensors.  
Attach the mini RJ11 plug of the sensor(s) to the appropriate T/H port.  

Connecting to the Unit 

Serial (RS232) Port 

The Switched Cabinet Distribution Unit is equipped with an RJ45 Serial RS-232 port for attachment to a PC or 
networked terminal server using the supplied RJ45 to RJ45 crossover cable and RJ45 to DB9F serial port adapter as 
required. For more information about the Serial RS-232 port, see the “Data Connections” section in Appendix C: 
Technical Specifications.  

 

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов