Sermatec SMT-100kWh Скачать руководство пользователя

Страница: 5 / 66

SHANGHAI SERMATEC ENERGY TECHNOLOGY CO.,LTD

- 2 -

1.5 Symbol usage

In order to ensure the safety of users and property when using this

product, or to use this product efficiently and optimally, the manual

provides relevant information and highlights it with appropriate

symbols.

The following lists some symbols which may be used in this manual.

Please read them carefully to make better use of this manual.

Danger

"Dangerous" indicates a highly potentially dangerous situation that, if

not avoided, could result in death or serious injury.

Warning

"Warning" indicates a moderate potential hazard, if not avoided, could

lead to death or serious injury.

Caution

"Caution" indicates a low-level potential hazard, if not avoided, could

lead to a situation that could result in moderate or minor injury.

Notes

"Caution" indicates a potentially hazardous situation that, if not

avoided, could result in equipment that may not function properly or

cause property damage.

Please pay attention to the danger warning signs on the body. The

signs include:

Содержание SMT-100kWh



































































Результаты поиска

Содержание SMT-100kWh

Отзывы:

Похожие инструкции для SMT-100kWh

Бренды по названию

Популярные бренды

Sermatec SMT-100kWh, Руководство пользователя

Результаты поиска

Содержание SMT-100kWh

Отзывы:

Похожие инструкции для SMT-100kWh

Бренды по названию

Популярные бренды