Sermatec SMT-100kWh Скачать руководство пользователя

Страница: 4 / 66

SHANGHAI SERMATEC ENERGY TECHNOLOGY CO.,LTD

- 1 -

1 About this manual

1.1 Preface

Dear customer, thank you very much for using the industrial and

commercial energy storage products developed and produced by

Shanghai Sermatec Energy Technology Co., Ltd. We sincerely hope this

product can meet your needs, and hope you can put forward more

opinions on the performance and function of the product . We will

continue to improve the product quality.

1.2 Model definition

The definitions of the product models involved in this manual are

shown in Figure 1-1:

SMT

100kWh

Nominal maximum system capacity: 100kWh

Power level: 50kW / 100kWh

SMT-100kWh: The maximum output power is 50kW, compatible with

30kW. The nominal capacity of the battery system is 100kWh.

1.3 Applicable personnel

This manual is intended for personnel who operate, maintain, and

perform other tasks on energy storage products. The reader needs

some electrical knowledge and is familiar with the electrical

schematics and the characteristics of electronic components.

1.4 Manual Use

Please read this manual carefully before using this product. Replace

this manual and other materials in the product components and store

them together, and ensure that relevant personnel can easily access

them.

ShanghaiSermatec Energy Technology Co., Ltd.

Содержание SMT-100kWh



































































Результаты поиска

Содержание SMT-100kWh

Отзывы:

Похожие инструкции для SMT-100kWh

Бренды по названию

Популярные бренды

Sermatec SMT-100kWh, Руководство пользователя

Результаты поиска

Содержание SMT-100kWh

Отзывы:

Похожие инструкции для SMT-100kWh

Бренды по названию

Популярные бренды