SEPTENTRIO PolaRx4 PRO Скачать руководство пользователя страница 16

Страница: 16 / 21

_____________________________________________________ 1 PolaRx4_PRO and PolaRx4TR_PRO

PolaRx4 Product Family Hardware Manual v2.0.0

Cable Name: CBLe_USB

Part #:

201202

USB cable to be connected to the COM3-4/USB connector.

Cable Name: CBLe_ETH_MS

Part #:

200418

Ethernet to hub/switch (straight) (RJ45). To be connected to the ETH connector.

Cable Name: CBLe_ETH_MX

Part #:

200417

Ethernet to PC (crossed) (RJ45). To be connected to the ETH connector.

Cable Name: CBLe_PWR_OE

Part #:

200422

Open-ended cable for the PWR connector (see pinout in section 1.2.8).

Pin#

Function

Wire Color

Power

Blue and green (these two wires are both connected to Pin#1)

ON/OFF

Red

GND

Black and Purple (these two wires are both connected to Pin#3)

1.7

Internal Logging on SD Memory Card

The receiver incorporates a SD memory card for internal logging. Refer to the “

How-to…

” section of

the Firmware User Manual to learn how to use this feature.

To prevent data corruption, logging is protected against accidental power outages. There is no need to
unmount the SD memory card before switching off the receiver.

1.8

Stand-By Mode

The receiver can be put in stand-by mode by entering the command “

exePowerMode, StandBy

”

(see Command Line Interface Reference Guide).

Waking up from stand-by mode is done by sending characters to the COM1 serial port.

For remotely-operated receivers, make sure that COM1 is remotely accessible before putting the receiver

in stand-by mode.

1.9

Applicable Software Package

PolaRx4_PRO and PolaRx4TR_PRO are compatible with Septentrio’s SSRC4 Software Packages.

Содержание PolaRx4 PRO






















Результаты поиска

Содержание PolaRx4 PRO

Отзывы:

Похожие инструкции для PolaRx4 PRO

Бренды по названию

Популярные бренды

SEPTENTRIO PolaRx4 PRO, Руководство по оборудованию

Результаты поиска

Содержание PolaRx4 PRO

Отзывы:

Похожие инструкции для PolaRx4 PRO

Бренды по названию

Популярные бренды