SEPTENTRIO mosaic Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 57

background image

28

28

mosaic Integration

28

5

mosaic Integration

5.1

Minimal Design

A minimal design for single-antenna and dual-antenna modules is shown below. In both
cases:

•

All ground pins and the

pins marked “

Reserved_GND

”

are connected to ground

(GND).

•

A 3.3VDC supply is provided to the VDD_3V3 pins and to the VDD_BAT pin. A 22µF
decoupling capacitor is recommended.

•

To provide power to the antenna(s), the VANT pins are also connected to the 3.3V
supply.

•

The 2V8_IN and 2V8_OUT pins are connected, as no external frequency reference
is used (see section 4.7).

•

The REF_I and REF_O pins are connected for the same reason.

•

1V8_OUT is connected to SYNC (this must always be the case).

•

Pin A3 (RTC_XTALI) needs to be connected to ground.

•

All other pins are left unconnected.

For easier debugging during host design development, it is recommended to always route
at least one of the COM ports to test pads or a test header.

«
...
26
27
28
29
30
...
»

Содержание mosaic Series


























































Отзывы:

Нет отзывов

Похожие инструкции для mosaic Series

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: jbc Страницы: 4

Бренд: Aalborg Страницы: 128

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Magellan Страницы: 2

Бренд: National Instruments Страницы: 2

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

PetroVend PV200

Бренд: OPW Страницы: 2

VBA-2E-G11-I/U/PT100-F

Бренд: Pepperl+Fuchs Страницы: 24

NovoCon S Digital

Бренд: Danfoss Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды