SEPTENTRIO AsteRx SB3 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 45

background image

CHAPTER 1. INTRODUCTION

1.1.4 Support

For ﬁrst-line support please contact your Septentrio dealer.

Additional documentation can be found in the following manuals:

•

The AsteRx SB3 Reference Guide

(available from the Support section of the

Septentrio website) includes information on the receiver operation, the full list of
receiver commands and a description of the format and contents of all SBF (Septentrio
Binary Format) blocks.

•

The RxTools Manual

covers the RxTools software suite, including RxControl and

RxLogger.

•

The Knowledge Base

on the Septentrio website contains a large number of articles

and application notes which cover a wide array of technical and less technical topics.
The Knowledge Base is part of Septentrio

’

s Support Portal which can be accessed

through the support section of the Septentrio website (see below).

The Septentrio website has a dedicated Support section
(http://www.septentrio.com/support), where the User Manual, the Firmware Reference
Guide and the latest o

ﬃ

cially supported Firmware version are readily available for download.

In case the AsteRx SB3 does not behave as expected and you need to contact Septentrio

’

s

Technical Support department, you should attach a short SBF log

ﬁ

le containing the support

blocks and a Diagnostic Report of the receiver.

http://www.septentrio.com

Headquarters

Septentrio NV

Phone: +32 16 300 800

Greenhill Campus

Fax: +32 16 221 640

Interleuvenlaan 15i,

[email protected]

3001 Leuven,

Belgium

6

«
...
4
5
6
7
8
...
»

Содержание AsteRx SB3














































Отзывы:

Нет отзывов

Похожие инструкции для AsteRx SB3

Бренд: NAD Страницы: 20

Бренд: Sandstrom Страницы: 36

Бренд: D+M Group Страницы: 19

Fine Arts M 100-A

Бренд: Grundig Страницы: 32

Бренд: Yaesu Страницы: 165

Бренд: HopeRF Страницы: 72

Бренд: DGTEC Страницы: 26

Бренд: Genius Страницы: 2

Бренд: Icom Страницы: 64

Бренд: Nakamichi Страницы: 36

LAS VEGAS 7 645 650 310

Бренд: Blaupunkt Страницы: 72

Бренд: World Vision Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: Philco Страницы: 39

Бренд: Harman Kardon Страницы: 52

Бренд: Denon Professional Страницы: 16

Cinergy 800 ePVR

Бренд: TerraTec Страницы: 14

Бренд: Rockford Fosgate Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды