SEPTENTRIO AsteRx SB3 Скачать руководство пользователя страница 44

Страница: 44 / 45

A.3 ETH

Figure A-3:

Solder view of the 4-pin female ETH socket on the rear panel of the

AsteRx SB3

The 4-pin connector type is an ODU M

-SNAP F Circular Connector Series S40F1C-P04MFG0-50OO.

PIN #

Name

Description

TXP

Ethernet TX+

TXN

Ethernet TX-

RXP

Ethernet RX+

RXN

Ethernet RX-

A.4 MAIN ANT / AUX ANT (TNC)

Connect an active GNSS antenna to these connectors. The gain at the connectors (antenna
gain minus cable losses) must be in the range 15 to 50dB.

The receiver provides a 5V DC supply on both the MA

N and AUX connectors to feed the

antennas. The maximum supported current is 200mA.

Never inject a DC voltage into the MA

N or AUX connectors as it may damage the receiver.

When using a splitter to distribute the antenna signal to several receivers, make sure that no
more than one output of the splitter passes DC. Use DC-blocks otherwise.

Содержание AsteRx SB3














































Результаты поиска

Содержание AsteRx SB3

Отзывы:

Похожие инструкции для AsteRx SB3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx SB3, Руководство пользователя

Результаты поиска

Содержание AsteRx SB3

Отзывы:

Похожие инструкции для AsteRx SB3

Бренды по названию

Популярные бренды