SEPTENTRIO AsteRx-m3, Руководство пользователя

Страница: 11 / 36

11
11
AsteRx-m3 OEM
11
2.5.1 30-pin Connector
Connector type: Hirose 30 pins DF40HC (3.5)-30DS-0.4V(51)
Mating connector: Hirose DF40C-30DP-0.4V(51)
See the pin numbering convention in the above picture.
Pin# Name Type Level Description Comment
1 Vin
P 3.3V
+/-5% Main power supply input Both Vin pins (pin#1 and pin#2) must
be tied together.
3 GND Gnd 0 Ground.
5 USB_D+ I/O USB USB data signal positive D+.
7 USB_Vbus Ctrl 4.40V
≤V≤
5.25V
USB VBUS.
This pin cannot be used to power the receiver!
Mandatory if USB is used.
See section 2.12
9 TX1 O LVTTL Serial COM 1 transmit line (inactive state is high)
11 GND Gnd 0 Ground.
13 TX2 O LVTTL Serial COM 2 transmit line (inactive state is high)
15 TX3 O LVTTL Serial COM 3 transmit line (inactive state is high)
17 GND Gnd 0 Ground.
19 EventA I, PD LVTTL Event A input. See section 2.8
21 PPS2 O LVTTL Second PPS output. Output impedance: 50 ohms. Output current:
24 mA. Polarity and rate user selectable independently of PPS1 on
pin#12. During start up, this pin is floating, See Reference Guide for
operating instructions. Pulse duration controllable with the
setPPS2Parameters command (default: 5ms).
External pull up/down can be used to
impose level during start up.
23 GND Gnd 0 Ground.
25 Button I, K LVTTL Input can be connected to a push button used to control SD card
logging. Low state is interpreted as “button pressed”.
Debouncing must be done externally
(no debouncing circuit on board).
See also section 2.11.
27 LOGLED O LVTTL Internal logging status indicator.
Max output current: 10 mA; output impedance: 20 Ohms See Appendix A
29 GND Gnd 0 Ground.
Pin# Name Type Level Description Comment
2 Vin
P 3.3V
+/-5% Main power supply input Both Vin pins (pin#1 and pin#2) must be
tied together.
4 GND Gnd 0 Ground.
6 USB_D- I/O USB USB data signal negative D-.
8 nRST Ctrl,PU LVTTL Reset input, active negative. Receiver resets when driven low.
10 RX1 I, K LVTTL Serial COM 1 receive line (inactive state is high).
12 PPS1 O,PD LVTTL First PPS output. Output impedance: 50 ohms. Output current: 24
mA. Polarity and rate user selectable. During start up, this pin is
pulled low with a 100-kOhm resistor.
See Reference Guide for operating instructions. Pulse duration
controllable with the
setPPSParameters command (default: 5ms).
14 RX2 I, K LVTTL Serial COM 2 receive line (inactive state is high).
16 RX3 I, K LVTTL Serial COM 3 receive line (inactive state is high).
18 VANT P 3<
VANT
< 5.5V Antenna supply. See section 2.4.1
20 nPDN Ctrl,PU LVTTL Receiver is put in standby mode (low power mode) when driven low.
Normal operation resumes when the pin level is high.
22 GPLED O LVTTL General purpose LED.
Max output current: 10 mA; output impedance: 20 Ohms See Appendix A
24 Reserved
26 SD_CLK O LVTTL SD card CLK line See section 2.11
28 SD_CMD O LVTTL SD card CMD line See section 2.11
30 SD_DAT0 I/O LVTTL SD card DAT0 line See section 2.11
1 29
30 2