SEO CANblu IMMOBILIZER – USER MANUAL
Disarming –
automatic when the ID transmitter is within the range of the main unit.
Arming
– automatic, 10 sec after losing connection between the ID transmitter and the main unit.
ID transmitter has a button in its right-hand hole, by which a user can operate it (use a paper clip). LED is
located in the left-hand hole of the ID transmitter.
During normal operation, the ID transmitter does not signal its state by LED, which increases the battery
life. For extra security we recommend you do not attach the ID to your car keys.
v 1.0 150219
Number of ID’s
button presses
Function
ID’s LED indication
Press and hold
(for 5 seconds)
Turning the ID transmitter ON or OFF
5 blinks (in 2 sec) – ID has been switched ON
Continuous illumination (in 2 sec) – ID has been
switched OFF
1x
ID ON or OFF status info
5 blinks (in 2 sec) – ID is ON
Continuous illumination (in 2 sec) – ID is OFF
2x
Service mode ON or OFF status
(while ID is ON and in range of main unit)
1 blink – service mode is OFF
2 blinks – service mode is ON
No blink – out of range
3x
ID status: connection with the main unit and
whether the ID transmitter is in range of main unit
(while ID is ON)
Single blinks for 20 seconds – ID out of range
Double blinks for 20 seconds – ID in range of main unit
3 fast blinks – ID does not store any encryption keys
4x
Checking ID’s battery level
(while ID is ON)
1 blink – battery nearly discharged
2 blinks – low charge level
3 blinks – sufficient charge level
4 blinks – high charge level
5x
Checking qty of IDs programmed into main unit
(while ID is ON and in range of main unit)
Number of blinks = number of programmed IDs
6x
Checking, if the sequence of buttons to disarm
the immobilizer was set in the vehicle (i.e. PIN
code, alternative to the ID transmitter)
(while ID is ON and in range of main unit)
1 blink – NO
2 blinks – YES
7x
Switching the
service mode
ON/OFF
(while ID is ON and in range of the main unit;
not later than 60 seconds after switching the
ignition ON)
A series of very fast blinks confirms sending the request
to the main unit. 5 blinks of dashboard indicator confirm
setting the
service mode
ON; 1 blink confirms setting the
service mode
OFF
8x
Checking current power of the ID transmitter
(while ID is ON)
1 to 9 blinks indicate the transmitter signal level
9x
Setting the transmitter emitted power, removing the encryption keys from the ID transmitter, removing
lost ID from the main unit and PIN code from the main unit
Additional code
ID’s LED indication
(a)
1-1-1-1 + 1 press & hold to set power -40 dBm
LED will briefly go OFF and ON to confirm entering each
digit. After entering all 4 digits of additional code, a press
& hold action (until the LED goes OFF) is required for
the settings to take effect. After releasing the button, LED
will blink rapidly if the emitted power-level setting was
set or if encryption keys were removed from the ID
transmitter
1-1-1-2 + 1 press & hold to set power -20 dBm
1-1-1-3 + 1 press & hold to set power
-16 dBm
1-1-1-4 + 1 press & hold to set power -12 dBm
1-1-1-5 + 1 press & hold to set power -8 dBm
1-1-1-6 + 1 press & hold to set power -4 dBm
1-1-1-7 + 1 press & hold to set power 0 dBm
1-1-1-8 + 1 press & hold to set power +3 dBm
1-1-1-9 + 1 press & hold to set power +4 dBm
(b)
1-2-3-1 + 1 press & hold to remove encryption
keys (while ID is OFF)
(c) 1-2-3-5 + 1 press & hold to remove PIN code
The ID transmitter must be switched ON
See the manual for details
(d)
1-2-3-9 +1 press & hold to remove ID
transmitters keys from the main unit
