background image

 

 

 

 

 

 

ISFET pH-sensor kit  

Technical guide 

 

Contents 

 

 

Description..................................................................................................................................2 

 

Specifications ..............................................................................................................................3 

 

Electrical connections..................................................................................................................4 

3.1 

Analog front-end module.....................................................................................................4 

3.2 

AD Converter module ..........................................................................................................4 

3.3 

USB Interface module ..........................................................................................................5 

 

Calibration ..................................................................................................................................6 

 

Data communication ...................................................................................................................7 

5.1 

Protocol ...............................................................................................................................7 

5.2 

Examples .............................................................................................................................8 

5.2.1 

Performing a single point calibration ............................................................................8 

5.2.2 

Performing a multi-point calibration ............................................................................9 

5.2.3 

Retrieving the pH signal ............................................................................................. 10 

5.2.4 

Retrieving the temperature signal .............................................................................. 10 

5.2.5 

Retrieving the slope values ........................................................................................ 11 

5.3 

ASCII table ......................................................................................................................... 12 

 
 
 
 
 

 E7500347.02

 

 

Содержание A120-001













Отзывы: