SenTech STC-MBS322U3V Скачать руководство пользователя страница 60

Страница: 60 / 65

No.15S103-01

60/65

STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V

Specifications and Use

’s guide

MultiROIsInMultiPayloads

MultiROIs In MultiPayloads.

MultiROIRegistersValid

Returns if the current ROI register set is valid and consistent.

Name

Description

AcquisitionMode

Sets the acquisition mode of the device. It defines mainly the number of frames to capture

during an acquisition and the way the acquisition stops.

AcquisitionStart

Starts the Acquisition of the device. The number of frames captured is specified by

AcquisitionMode.

AcquisitionStop

Stops the Acquisition of the device at the end of the current Frame. It is mainly used when

AcquisitionMode is Continuous but can be used in any acquisition mode.

AcquisitionArm

Arms the device before an AcquisitionStart command. This optional command validates all the

current features for consistency and prepares the device for a fast start of the Acquisition.

AcquisitionFrameRate

Controls the acquisition rate (in Hertz) at which the frames are captured.

TriggerSelector

Selects the type of trigger to configure.

TriggerMode

Controls if the selected trigger is active.

TriggerSoftware

Generates an internal trigger. TriggerSource must be set to Software.

TriggerSource

Specifies the internal signal or physical input Line to use as the trigger source. The selected

trigger must have its TriggerMode set to On.

TriggerDelay

Specifies the delay in microseconds (us) to apply after the trigger reception before activating it.

ExposureMode

Sets the operation mode of the Exposure (or shutter).

ExposureTimeSelector

Selects which exposure time is controlled by the ExposureTime feature. This allows for

independent control over the exposure components.

ExposureTime

Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This controls

the duration where the photosensitive cells are exposed to light.

ExposureTimeAbs

Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This controls

the duration where the photosensitive cells are exposed to light.

ExposureTimeRaw

Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This controls

the duration where the photosensitive cells are exposed to light.

ExposureAuto

Sets the automatic exposure mode when ExposureMode is Timed. The exact algorithm used to

implement this control is device-specific.

ExposureAutoLimitMax

Determine the upper limit of exposure time when ExposureAuto is set to Continuous.

ExposureAutoLimitMin

Determine the lower limit of exposure time when ExposureAuto is set to Continuous.

Name

Description

PayloadSize

Provides the number of bytes transferred for each image or chunk on the stream channel. This

includes any end-of-line, end-of-frame statistics or other stamp data. This is the total size of

data payload for a data block.

Name

Description

LineSelector

Selects the physical line (or pin) of the external device connector to configure.

LineMode

Controls if the physical Line is used to Input or Output a signal.

LineInverter

Controls the inversion of the signal of the selected input or output Line.

LineStatus

Returns the current status of the selected input or output Line.

LineSource

Selects which internal acquisition or I/O source signal to output on the selected Line. LineMode

must be Output.

UserOutputSelector

Selects which bit of the User Output register will be set by UserOutputValue.

Содержание STC-MBS322U3V


































































Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды

SenTech STC-MBS322U3V, Технические характеристики

Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды