SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 47

Страница: 47 / 52

UltraWave Product Guide

Page 47

Parts list

Component

Part Number Description

UltraWave microwave sensor system

UltraWave sensor
system

E4FG0101

UltraWave transmitter and receiver pair with two mounting kits and four cable
glands

UltraWave transmitter unit

transmitter unit

E4EM0101

replacement transmitter unit with mounting kit and two cable glands

UltraWave receiver unit

receiver unit

E4EM0201

replacement receiver unit with mounting kit and two cable glands

UltraWave accessories

mounting kit

E4KT0300

two mounting kits and four cable glands

UCM

00SW0100

Universal Configuration Module software, Windows-based application, setup,
calibration and diagnostic tool

UCM cable

GE0444

UCM interface cable, 3 m, USB (connects PC running UCM to processor)

Network accessories

Silver Network
Interface Unit

00EM0200

Silver Network data converter for EIA-422 and multimode fiber optic
applications

Silver Network
Interface Unit

00EM0201

Silver Network data converter for EIA-422 and singlemode fiber optic
applications

Network Manager

00FG0200

Network Manager CD containing Network Manager application software for
the Silver, Crossfire, MX, VoE, and Sennet networks (Windows application)

UltraLink

00FG0220

UltraLink CD containing Network Manager service software for the Silver
Network (Windows Service)

Alarm Interface
Module

00SN0230

Security Management System (Windows application) for use with Network
Manager requires USB security key

Network Interface
Card (multimode
fiber)

00BA1901

Network interface card for multimode fiber optic communications

Network Interface
Card (EIA-422)

00BA2000

Network interface card for copper wire communications

Network Interface
Card (singlemode
fiber)

00BA2101

Network interface card for singlemode fiber optic communications

Содержание UltraWave E4FG0101





















































Результаты поиска

Содержание UltraWave E4FG0101

Отзывы:

Похожие инструкции для UltraWave E4FG0101

Бренды по названию

Популярные бренды

SENSTAR UltraWave E4FG0101, Руководство по эксплуатации продукта

Результаты поиска

Содержание UltraWave E4FG0101

Отзывы:

Похожие инструкции для UltraWave E4FG0101

Бренды по названию

Популярные бренды