SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 52

background image

UltraWave Product Guide

Page 43

Verifying the UltraWave alignment

If the UltraWave sensor is encountering detection problems it is possible that one of the unit’s may
be out of alignment. The UltraWave receiver includes a received signal strength indicator (RSSI)
as an alignment aid (LEDs D6 - D13).

1. Remove the lower cover from the receiver unit.

2. Press and hold the tamper switch, while observing the RSSI (LEDs D6 - D13). Do not obstruct

the receiver’s antenna while observing the RSSI.

3. Note the received signal strength (e.g., LED D7 ON).

4. Adjust the horizontal and vertical alignment of the receiver unit slightly to determine if the

received signal can be improved. Recheck the RSSI level.

5. Adjust the horizontal and vertical alignment of the transmitter unit slightly to determine if the

received signal can be improved. Recheck the RSSI level at the receiver unit.

6. Once the alignment is complete, connect the UCM and select the Recalibrate button.

7. Replace the lower cover on the receiver unit.

Figure 34 LEDs D6 - D13 RSSI alignment aid

D6 - maximum received signal strength

D13 - minimum received signal strength

D9 - minimum operational signal strength

(operational range D9 to D6)

«
...
41
42
43
44
45
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: Radionics Страницы: 10

Бренд: Falltech Страницы: 52

Бренд: Panasonic Страницы: 124

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 1

Toolsplit TSCE-500

Бренд: Tecnosystemi Страницы: 8

Бренд: Rae Страницы: 2

Бренд: ADT Страницы: 29

Бренд: Y-cam Страницы: 12

Бренд: Iget Страницы: 8

Бренд: unii Страницы: 2

Бренд: Abus Страницы: 4

Бренд: nedis Страницы: 37

Бренд: i-PRO Страницы: 26

SpectrAlert S900RLFIRE

Бренд: System Sensor Страницы: 2

ClareOne CLR-C1-WTR

Бренд: clare Страницы: 2

PRO-9642a Pursuit Series

Бренд: Audiovox Страницы: 8

Бренд: D-MAX Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды