SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 52

background image

UltraWave Product Guide

Page 31

3

Setup and calibration

Setup

UltraWave setup and calibration is done using Senstar’s Universal Configuration Module (UCM).
The UCM is a Windows-based software application that performs the calibration, setup,
maintenance and diagnostic functions for Senstar’s line of intrusion detection sensors. The UCM
connects directly to the UltraWave unit via USB. Network based UltraWave receivers can also
connect remotely via the Silver Network Manager.

Senstar recommends that the initial calibration be done at the UltraWave unit using a direct USB
connection to the UCM.

The UltraWave receiver setup requires the following configuration settings:

•

specify the

Locale

-

FCC

for North American applications,

ETSI

for European applications

(transmitter and receiver settings must match)

•

specify the

Frequency Pair

(transmitter and receiver settings must match)

•

enter the

Transmitter Serial Number

•

set the detection

Thresholds

(use the UCM Height Calculator tool to determine the optimum

detection Thresholds)

The UltraWave transmitter setup requires the following configuration settings:

•

specify the

Locale

-

FCC

for North American applications,

ETSI

for European applications

(transmitter and receiver settings must match)

•

specify the

Frequency Pair

(transmitter and receiver settings must match)

Once the UltraWave transmitter and receiver are properly installed and configured, you can
calibrate the receiver unit. On the receiver’s UCM Status tab, select the recalibrate button and the
UltraWave receiver will auto-calibrate to provide the best possible received signal strength (see

Receiver calibration on page 38

Note

UltraWave setup and calibration should be performed by a qualified
technician.

Note

Consult the online help for detailed information on UCM operation.

«
...
29
30
31
32
33
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: V-Tec Страницы: 24

Бренд: Samsung Страницы: 1

Бренд: VADDIO Страницы: 20

WallVIEW CCU HD-18 HD-SDI

Бренд: VADDIO Страницы: 18

Бренд: VADDIO Страницы: 60

Бренд: Vacron Страницы: 2

CLEARVIEW HD-18

Бренд: VADDIO Страницы: 4

Бренд: Vivotek Страницы: 2

Бренд: Vivotek Страницы: 2

Elite RESPTZ37-1

Бренд: Revo Страницы: 65

Бренд: eZLO Страницы: 10

Бренд: Ganz Страницы: 24

Бренд: Zumimall Страницы: 28

PRO-9642a Pursuit Series

Бренд: Audiovox Страницы: 8

Бренд: Inter-m Страницы: 18

Бренд: Camlux Страницы: 90

Бренд: Conrad Страницы: 70

Бренд: Defender Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды