manualshive.com logo in svg

senseFly EBEE RTK, Расширенное руководство пользователя

Поделиться
Скачать
senseFly EBEE RTK Скачать руководство пользователя страница 179

Troubleshooting

10.5

Resetting default camera settings

In case of unwanted configuration changes, the camera can be re-configured to
a suitable state. Please refer to your camera user manual for the procedure. You
can find camera manuals in our Knowledge Base within my.senseFly⁶³

10.6

Improving radio signal communication

You may occasionally lose the data connection between

eMotion

and your

eBee RTK

while in the field. Whether there is a loss in uplink or downlink communication,
the drone will continue flying along its Flight Plan and should re-establish the
connection as it flies closer to the base station or changes direction.

If the drone stops receiving messages from

eMotion

(uplink direction) for more

than 30 s you will see a ‘Data uplink lost’ In-flight warning appear in

eMotion

.

If for safety reasons you would like the

eBee RTK

to automatically return to the

Home waypoint when this warning appears, select the corresponding option in
the Flight Parameters tab⁶⁴.

If there are no more messages received by

eMotion

from the drone (downlink di-

rection), a ‘Data downlink lost’ message will appear in

eMotion

. If there is still an

active uplink connection you may still command your drone to return to the Home
waypoint using the Control Bar.

Data connection range can be effected by many external factors such as antenna
height, terrain and obstacles or radio interference. We recommend the following
tips to improve the range of your connection in the field:

1. Place the USB ground modem as high as possible (for example, on top of a

car, ladder or nearby building). A height of at least 2 m is recommended.

2. Ensure that the USB ground modem’s antenna is pointing straight up.

3. Disable any 2.4 GHz-based communication devices (or put them into ‘Air-

plane mode’) in the vicinity of the USB ground modem. This includes all

⁶³ http://my.sensefly.com
⁶⁴ see section ‘Flight Parameters tab’ on page 136 for more details

179

Содержание EBEE RTK































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды