manualshive.com logo in svg

senseFly EBEE RTK, Расширенное руководство пользователя

Поделиться
Скачать
senseFly EBEE RTK Скачать руководство пользователя страница 161

Troubleshooting

10.2

Take-off vetoes

After successfully completing pre-flight checks the status LED becomes a solid
green to indicate that the drone is ready for take-off. At this point the

eBee RTK

continues to monitor its sensors and battery level. If at any point the drone detects
a condition that prevents it from beginning the automatic take-off procedure it
displays a Take-off veto in

eMotion

and the status LED changes to a blue pulse.

Once the Take-off veto is cleared the status LED returns to a solid green colour to
indicate that the drone is ready for take-off.

Table 4 on the next page presents all the Take-off vetoes that may occur and pos-
sible actions to remove the veto. If a veto persists after performing the suggested
action, we recommend you report the problem by following the instructions in
section ‘Reporting a problem with your

eBee RTK

’ on page 181.

161

Содержание EBEE RTK































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды